14
Valco Melton
IS0231
Vacuum Feeder Assembly Instructions
c.
If the adhesive is at the appropriate level and the
light is red carefully turn the screw clockwise until the
light changes to intermittent red-yellow.
d.
After 3 seconds it should change to green.
e.
If the adhesive is at the appropriate level and the
light is green, turn the screw, carefully, counter
clockwise until the light changes to intermittent red-
yellow.
f.
After 3 seconds it should change back to green.
9.
Remove half of the adhesive and close the lid. Be sure that the
light on the amplifier box turns red.
10. Allow the unit to refill. Make sure the light is green and the
adhesive is at the appropriate level.
a.
If the adhesive is not at the appropriate level, repeat
step 8.
CAUTION!
CAUTION!
CAUTION!
CAUTION!
CAUTION!
Check the adhesive level periodically to confirm the
sensor is working properly.
CAUTION!
CAUTION!
CAUTION!
CAUTION!
CAUTION!
The adhesive pile will be uneven; measure from the top
of the pile to the top of the tank.
6.
If the unit does fill to the appropriate level, proceed to step 7.
7.
Remove the protective screw on the amplifier box.
8.
Adjust the sensor calibration, using a small, flat-head screwdriver
to adjust the calibration screw on the amplifier box.
a.
Turn the screw counter clockwise to raise the
adhesive level.
b.
Turn the screw clockwise to lower the adhesive level.
Calibration - Continued
Summary of Contents for D10
