4
Valco Melton
IS0213
Pressure Switch Installation Instructions
Calibrating the Pressure Switch -
Continued
7.
Connect the ring terminal to the chassis, using one of the ground
studs.
8.
Turn the unit on and allow the adhesive to become molten.
9.
Adjust the pressure relief to the desired switch pressure.
10. Slide the adjustment cover forward, carefully, away from the
manifold.
Warning!
Warning!
Warning!
Warning!
Warning!
The pressure switch will be hot!
11. Use a 3/16" flathead screwdriver, or a 1/4" wide blade, to adjust
the castle nut.
a.
Insert the screwdriver or blade and turn clockwise to
increase the set point, or counter-clockwise to
decrease the set point. Adjust the nut accordingly
until the switch clicks.
12. Adjust the adhesive pressure to be below, and above, the set
point while verifying that the led on the control board for that input
is turning on and off.
a.
If the switch does not turn on and off as expected,
repeat step 11.
13. Slide the adjustment cover closed carefully.
Warning!
Warning!
Warning!
Warning!
Warning!
The pressure switch will be hot!
14. Close the front operator panel.
Enabling Pressure
Switch Input
1.
Close the front operator panel.
2.
Turn the unit on, if it is not already.
3.
Go to the setting screen by pressing
.
4.
Unlock the control, using the level-3 password, “6550”.
Summary of Contents for D10
