![background image](http://html1.mh-extra.com/html/valco-melton/d10/d10_manual_849617021.webp)
MM113 - D10/D16 Hot Melt Unit
Section 2 - Safety and Use
21
Hose Safety Information
DO NOT
DO
Do not
use bindings, wire
ties, or unapproved
fasteners around the
hoses.
Do
use approved wrapping
(P/N 775xx827), making
sure the wrapping is slightly
snug but not tight.
Do not
place hoses close
together.
Do
allow at least 2 inches
(5.1 cm) between hoses for
proper ventilation.
Do not
bend hoses
sharply.
Do not
allow kinks
or indentations in the
hoses.
Do
use a minimum bend
radius of 10 inches for a 20-
inch diameter coil hose.
Do not
use unapproved
hooks to hang hoses.
Do
not
wrap hoses over or
around objects.
Do
use a hose hanging kit
(P/N 781xx827).
Do not
use the “one
handed/one wrench”
technique to attach or
remove hoses.
Do not
wrench on any surface
other than the large
hexagon swivel nuts.
Do
use two hands and two
wrenches to tighten or
loosen connections on
hoses.
Do
wrench only on
large hexagon swivel nuts.
Do not
allow hoses to rub
against objects or to come
into contact with sharp
edges or points.
Do
wrap the hoses in
approved padding (P/N
795xx549) if the hoses must
be installed where they will
come into contact with
objects.
Do not
use worn,
damaged, or bent hoses.
Do
inspect all hoses
regularly for damage and/or
wear and replace damaged
or worn hoses immediately.
Summary of Contents for D10
