5
Valco Melton
IS0213
Pressure Switch Installation Instructions
7.
To enable any of the inputs, select the desired function from the
list below.
Input
Disabled
Hose On/Off
All Heaters On/Off
Pump On/Off
Auto Setback
Setback
Pressure Fault
The pressure switch can also be
hooked into another controller. If
another controller is used, follow the
wiring chart provided in “Calibrating the
Pressure Switch,” step 5, and verify the
pin location for that controller.
The pressure fault setting can be used
with a beacon, to give a visual/audible
signal, by setting the beacon to “Alarm”.
Valco Cincinnati Incorporated
411 Circle Freeway Drive
Cincinnati, Ohio 45246, USA
TEL: (1) 513-874-6550
FAX: (1) 513-874-3612
Melton S.L.U.
Pol. Industrial Agustinos
calle G, n. 34
31160 Orcoyen, Navarra, Spain
TEL: (34) 948-321-580
FAX: (34) 948-326-584
Valco Cincinnati, Ltd.
Unit 7-8
Hortonwood 32
Telford TF1 7YN England
TEL: (44) 1952-677911
FAX: (44) 1952-677945
Valco Cincinnati GmbH
Storkower Strasse 6
D-15749 Gallun, Germany
TEL: (49) 33764 8700
FAX: (49) 33764 87070
No part of this document may be reproduced without express permission from Valco Cincinnati, Inc. All rights reserved. Designs and other information may change without notice.
© 2011 Valco Cincinnati, Inc.
www.valcomelton.com
IS0213 10/11
5.
Return to the setting screen by pressing
again.
6.
Select the “Input” screen.
Summary of Contents for D10
