1
Valco Melton
HANDGUN SWITCH KIT INSTALLATION AND OPERATION
HANDGUN SWITCH KIT INSTALLATION AND OPERATION
HANDGUN SWITCH KIT INSTALLATION AND OPERATION
HANDGUN SWITCH KIT INSTALLATION AND OPERATION
HANDGUN SWITCH KIT INSTALLATION AND OPERATION
IS0161
7 / 1 2
7 / 1 2
7 / 1 2
7 / 1 2
7 / 1 2
Hot Melt Unit with Universal Control
1.
Turn off power to unit and open lid to electronics cabinet.
2.
Locate Control Board (151xx650) on the back of the Keypad. See figure below.
3.
Run flying lead end of the included Handgun Switch Cable Assembly up to the Control Board. If
your Handgun Switch Cable Assembly has a flange mounted connector, install it in place of the
knockouts provided in the back panel of the unit. Use hardware provided with kit.
4. If the cable assembly has a flange-mounted connector, route the cable assembly along the inside of
the unit, as shown.
Input 1
Input 2
Input 3
Input 4
Pin 2 (I1): Orange
Pin 5 (I2): Orange
Pin 8 (I3): Orange
Pin 11 (I4): Orange
Pin 3 (GND): Yellow
Pin 6 (GND): Yellow
Pin 9 (GND): Yellow
Pin 12 (GND): Yellow
Cable Connections
5.
Choose which of the four inputs that you want to connect to. Then connect the Yellow and Orange
wires from the Cable Assembly to the programmable inputs connector J23 on the Control Board as
follows.
If you use two Handguns and want both to activate an input, install the yellow and orange wires from each
cable in parallel.
If you want to use one Handgun Switch for two different functions (ie Pump On/Off and Auto Setback), then
connect to one of the inputs as shown in step 4; then run a jumper wire from where the Orange wire is landed
to the other input you want to use (I1-Pin 2, I2-Pin 5, I3-Pin 8, or I4-Pin 11).
6.
Discard the jumper wires included with the kit..
Summary of Contents for D10
