1
Valco Melton
INTERNAL LEVEL SENSOR INSTRUCTIONS
IS0232
DATE [5/12]
DATE [5/12]
DATE [5/12]
DATE [5/12]
DATE [5/12]
WARNING!
WARNING!
WARNING!
WARNING!
WARNING!
Read and follow all instructions, warnings, tag, and label
before operating the equipment. Only qualified
personnel should perform this procedure.
All equipment is to be installed and all connections are
to be made only by qualified personnel. Components
and accessories are to be installed in accordance with
the instructions provided and applicable codes for the
region installed.
USE OF THIS EQUIPMENT IN A MANNER OTHER
THAN DESCRIBED IN THIS INSTRUCTION SHEET
AND FAILING TO FOLLOW ALL INSTRUCTIONS
COULD RESULT IN PERSONAL INJURY, DEATH, OR
DAMAGE TO EQUIPMENT.
WARNING!
WARNING!
WARNING!
WARNING!
WARNING!
The equipment may still be energized even after the
circuit breaker or main power switch is off.
All equipment must be properly grounded and fused in
accordance with rate current consumption (refer to the
equipment identification plate).
Gauge and insulation for power supply must be
adequate to handle rated current consumption.
FAILING TO FOLLOW ALL INSTRUCTIONS COULD
RESULT IN PERSONAL INJURY, DEATH, OR
DAMAGE TO EQUIPMENT.
Important
Information
Description
This instruction sheet will cover how to install an internal level sensor in either
the low or high position. The sensor should be installed based on the
assembly part number.
Part Number
Position
776xx745 Low
776xx748 High
776xx751 Both
Installation
1.
Turn off the unit and disconnect the power.
2.
Open the back hose and front operator panels.
3.
Remove the two (2) M4 X 12 socket head cap screws holding the
lanyards to the top of the case.
Summary of Contents for D10
