MM113 - D10/D16 Hot Melt Unit
Appendix E - Communication Protocols-Ethernet IP
227
Appendix E - Communication Protocols-Ethernet IP
Hot Melt Unit to EthernetIP Communication Protocol
The Melter Communication Interface Ethernet/IP module is configured to use a consistent 16 bytes of process data.
When the Ethernet is enabled, the Melter control will initiate configuration setup with the Ethernet/IP module, and
configure the module, using the addresses stored in the setup menus.
When the Melter is started, the module can take up to two minutes to initialize. This is due to the Melter configuring
its own internal network before it starts configuring and initializing the Ethernet/IP module.
Data is carried in specific send and receive packets, in which the PLC initiates the commands needed for the Melter
process. Only one command is executed at a time, and the Melter will respond with specific fault codes if the
command cannot be executed. For each packet, the Melter will return the Data Index and channel from the PLC
command, to indicate proper acknowledgement.
Data Packets used for Ethernet/IP communication
This section describes the Process Data packets needed to operate between the Melter and PLC. There are two
types of packets:
Send Packets
that have the control information from the PLC and,
Receive Packets
that have the
status information from the Melter.
Some PLC messages may need to swap bytes in order to
correspond with the Melter message.
Send Packet (PLC) Frame
Byte0 Byte1 Byte2 Byte3 Byte4, 5
Control
Data Index
Pump1 speed%
Command
Byte6, 7 Byte8, 9
Channel
Data Value
Byte10, 11 Byte12, 13 Byte14, 15
Pump2 speed%
Pump3 speed%
Pump4 speed%
Not Used
Summary of Contents for D10
