IS0299 - D Series Coupling Upgrade Procedure
9
19. There should be some play in the spider after the coupling is assembled. Verify that the coupling can be
moved easily, by hand, approximately .020” (.50mm) in each direction shown in the figure below.
CAUTION!
If the spider does not have some play in the directions shown, the pump and motor shafts
may not be properly aligned, or there may not be sufficient axial clearance between the hubs
and the spider. Proceeding without correcting misalignment or axial clearance could cause
damage to the pump!
20. Turn the unit upright, reconnect power, and fill the tank with adhesive. Once the unit has reached
operating temperature and the adhesive has melted, start the pump. Verify that there is no noise from the
pump, and check the unit for vibration. If no abnormal conditions are observed, the unit is ready to be put
back in service.
© Valco Cincinnati, Inc.
www.valcomelton.com
IS0299
1/16
No part of this document may be reproduced without express permission from Valco Cincinnati, Inc. All rights
reserved. Designs and other information may change without notice.
Valco Cincinnati Incorporated
411 Circle Freeway Drive
Cincinnati, Ohio 45246, USA
TEL: (1) 513-874-6550
FAX: (1) 513-874-3612
Melton S.L.U.
Pol. Industrial Agustinos
calle G, n. 34
31160 Orcoyen, Navarra, Spain
TEL: (34) 948-321-580
FAX: (34) 948-326-584
Valco Cincinnati, Ltd.
Unit 7-8
Hortonwood 32
Telford TF1 7YN England
TEL: (44) 1952-677911
FAX: (44) 1952-677945
Valco Cincinnati GmbH
Bonnerstrasse 349
40589 Dusseldorf-Benrath,
Germany
Tel: +49 211 984 798-0
Fax: +49 211 984 798-20
Valco Melton France
Technoparc des Hautes Faventines
32 Rue Jean Bertin
26000 Valence
Tel: +33 (0)4 75 78 13 73
Fax: +33 (0)4 75 55 74 20
Summary of Contents for D10
