Appendix D - Communication Protocols-Modus MM113 - D10/D16 Hot Melt Unit
218
Hardware Considerations - Continued
9)
With jumpers installed on JP1-4 (currently installed), the board is configure for 2-wire RTU.
Can also be configured for 4-wire (without jumpers JP1-4).
10)
From RJ45 port (J2 on CPU board) Pin 1 is the Negative “A” comm. line and Pin 2 is the
Positive “B” comm. line. Pin 8 is the Ground reference. See Figure 2 below for RJ45 pin numbering.
Figure 2
11)
The 120 ohm load resistor for the Modbus network is built into the transceiver chip and can be
toggled by going into Setup Menu > ”Config” Menu > “Comm. Load Resistors” and Enabling “Modbus
RTU”.
Parameter List
Short Name
(Melton)
Modbus Hex Address
(NC Spec)
Write/Read
Description
Comments
Dep prog
0x0100
W/R
Tank Temperature Setpoint
All Temperatures in ºC
M1 prog
0x0101
W/R
Hose 1 Temperature Setpoint
All Temperatures in ºC
P1 prog
0x0102
W/R
Gun 1 Temperature Setpoint
All Temperatures in ºC
M2 prog
0x0103
W/R
Hose 2 Temperature Setpoint
All Temperatures in ºC
P2 prog
0x0104
W/R
Gun 2 Temperature Setpoint
All Temperatures in ºC
M3 prog
0x0105
W/R
Hose 3 Temperature Setpoint
All Temperatures in ºC
P3 prog
0x0106
W/R
Gun 3 Temperature Setpoint
All Temperatures in ºC
M4 prog
0x0107
W/R
Hose 4 Temperature Setpoint
All Temperatures in ºC
P4 prog
0x0108
W/R
Gun 4 Temperature Setpoint
All Temperatures in ºC
M5 prog
0x0109
W/R
Hose 5 Temperature Setpoint
All Temperatures in ºC
P5 prog
0x010A
W/R
Gun 5 Temperature Setpoint
All Temperatures in ºC
M6 prog
0x010B
W/R
Hose 6 Temperature Setpoint
All Temperatures in ºC
P6 prog
0x010C
W/R
Gun 6 Temperature Setpoint
All Temperatures in ºC
B1
0x010D
W/R
Tank Standby %
Not Used by Valco CPU
B2
0x010E
W/R
Hoses Standby %
Not Used by Valco CPU
Summary of Contents for D10
