![background image](http://html1.mh-extra.com/html/valco-melton/d10/d10_manual_849617230.webp)
Appendix E - Communication Protocols-Ethernet IP MM113 - D10/D16 Hot Melt Unit
230
Data Value Byte 4 and 5
This is the data that the PLC sends to the Melter to update a given parameter. This value is limited to the range listed
in the Data Index table, and will return an
Outside Range fault
otherwise.
Pump1 speed%...Pump4 speed% Byte 6 - 13
With each message from the PLC to the Melter, the PLC can send the Pump Manual speed down, to change the
pump pressures dynamically.
Receive Packet (Melter) Frame
Bit Definitions for Status Bytes 0 and 1
These are the response bytes sent back from the Melter at every message.
Bit 0: Melter Ready for Operation – 1 = Ready, 0 = Not Ready
Bit 1: Ready Delay Enabled – 1 = Enabled, 0 = OFF
Bit 2: System is in Alarm State – 1 = Alarm, 0 = No Alarm
Bit 3:
System is in Fault State – 1 = Fault, 0 = No Fault
Bit 4: Melter is Shutdown – 1 = Shutdown, 0 = Not Shutdown
Bit 5: Melter in Warmup State – 1 = Warmup active, 0 = Warmup not active
Bit 6: Melter in Setback – 1 = Setback active, 0 = Setback not active
Bit 7: Pump 1 Active – 1 = On, 0 = OFF
Bit 8: Pump 2 Active – 1 = On, 0 = OFF
Bit 9: Pump 3 Active – 1 = On, 0 = OFF
Bit 10: Pump 4 Active – 1 = On, 0 = OFF
Bit 11: Not used
Bit 12: Not used
Bit 13: Not used
Bit 14: Communication Fault (See Error Codes Section)
Bit 15: Communication Fault (See Error Codes Section)
Byte0, 1 Byte2 Byte3 Byte4, 5
Status
Data Index
Ch+1 Data
Byte6, 7 Byte8, 9
Channel
Ch Read Data
Byte10, 11 Byte12, 13 Byte14, 15
Ch+2 Data
Ch+3 Data
Ch+4 Data
Ch+5 Data
Summary of Contents for D10
