MM113 - D10/D16 Hot Melt Unit
Section 5 - Setup
63
Level Sensor Setup
Level 1 and 2
There are two types of level control typically used with the D-Series Units, an internal level sensor (Level 1) and an
external level sensor (Level 2). The internal level sensor can be used inside the tank of the unit to trigger an auto-fill
device (see hopper feeder below), or an alarm state. The external level sensor is used for pot fill mode (see Pot Fill
Mode - Section 5). The delay for these sensors to activate can be set in this screen.
Hopper Feeder - Internal Low Level Detection
The Hopper Feeder option is used to refill the hot melt control’s tank with fresh adhesive when the tank level drops
below the set level sensor. This eliminates the need for the operator to manually open the tank lid and add adhesive
to the tank.
The internal low level sensor is mounted in the hot melt control tank so that when the adhesive drops below the
sensor, a feeder valve is energized to feed glue into the tank to be melted. This feature has a safety door switch that
will disable the feeder if the tank door is opened. The door switch, internal level sensor and feeder valve need to be
connected to the CPU board, to operate properly.
The internal low level sensor plugs into J15 on the CPU board. This feature does not need to be set up in the
software. If the Hopper Feeder and it’s components are connected as described above, the valve will energize when
the door switch is closed and the sensor calls for glue.
Door Switch
The tank lid door switch will be wired to J14 on the CPU. The switch must be in the closed position for the feeder
valve to energize and add adhesive to the tank. When the tank lid is opened, the feeder valve will turn off.
Feeder Valve Operation
The feeder valve is a ded24VDC @ 0.5A output that will energize when the internal low level sensor calls for
glue and the door switch is closed. This is J17 on the CPU board; pin 1 is +24V, pin 2 is ground.
Internal Level Control
Feeder Valve Connector
Summary of Contents for D10
