VALCO MELTON D10, Manual

Page: 229 / 313

MM113 - D10/D16 Hot Melt Unit Appendix E - Communication Protocols-Ethernet IP
229
Data Index Byte 2
The Data Index is equal to the Melter Parameters that may be accessed through the Ethernet/IP protocol. Only those
parameters listed can be accessed through remote mode. Parameters that require a system restart, including most
setup parameters, will still need to be accessed at the Melter.
The following is the Data Index list and valid parameters.
If the system is in Local Operation mode, all Data Types become
Read Only and, in the case of Write Only Indexes , become
unavailable.
Data Index Channel Data Type Range Description
4 - RO 0 - 1 Remote Operation Mode (0=Local, 1=Remote)
7 - WO 0 - 1 Clear Fault
11 - RO 0 - 120 min Ready Delay Time Remaining
23 - RO 0x0000-0xFFFF Current Alarm Type (See Table Below)
110 - RW 0 – 1 Temperature Units (0=C, 1=F)
111 0-19 RW 0 – 1 Activate Temperature Zone
112 0-7 RW 0 – 1 Activate Hose/Gun Zone Pair
115 0-19 RW 40 – 230 C Zone Temperature Set Point
120 0-19 RO 40 – 230 C Zone Current Temperature
128 - RW 5 – 190 C Standby Temperature
135 - RW 0 – 1440 min AutoSetback Time
136 - RW 0 – 1440 min AutoStandby Time
142 - RW 5 – 60 C UnderTemp Fault Offset
152 - RW 5 – 60 C OverTemp Fault Offset
160 - RW 1 – 180 min Exit Standby Time
170 0-3 RW 0 – 2 Pump Auto Mode Input Speed Type
(0=0-10V, 1=0-2.8V, 2=Encoder)
171 0-3 RW 0 – 9999 m/min Pump Minimum Speed - Encoder
172 0-3 RW 0 – 9999 RPM Pump Creep Speed
173 0-3 RW 0 – 9999 Pump Ratio
174 0-3 RO 0 – 100% Pump Manual Speed
175 0-3 RW 0 - 1 Pump Mode
176 0-3 RW 0 – 200 Pump Gain
177 0-3 RO 0 – 1 Pump Enable
178 0-3 RW 0 – 1 Grammage Enable
179 0-3 RW 10 – 3000 mm Application Width (Grammage Only)
180 0-3 RW 1 – 200 g/m² Application Weight (Grammage Only)
181 0-3 RW 0.8 – 100 Density (Grammage Only)
182 0-3 RO 0 – 9999 RPM Pump Speed
183 0-3 RW 0 – 9999 mV Pump Minimum Speed - Tach
200 - RW 0 – 1 Seven-Day Clock Enabled
201 - RO 0 – 1 Seven-Day Clock Status
202 - RW 0 – 6 Clock – Day
203 - RW 0 – 24 Clock – Hour
204 - RW 0 - 60 Clock – Minute
Channel Byte 3
This is the location targeted within parameters having multiple zones.
For example - In Data Index 182 (Pump Speed):
Sending a read to channel 0, the Melter will send back the value for the Pump 1 current pump speed (channel 1 =
Pump 2, etc.)