manualshive.com logo in svg

Toshiba Tecra M9, Maintenance Manual, Page: 96 / 414

Share
Download
Toshiba Tecra M9 Maintenance Manual Download Page 96

2  Troubleshooting Procedures  

2.10 Modem Troubleshooting

 

Procedure 2 

Connector Check and Replacement Check 

The Modem is installed as a MDC (Modem Daughter Card). If the modem malfunctions, 
there may be a bad connection between the MDC and the system board. Or the MDC, system 
board or their connectors might be damaged. 

Disassemble the computer following the steps described in Chapter 4, 

Replacement 

Procedures

 and perform the following checks: 

Check 1  Make sure the MDC is firmly connected to CN3010 on the system board and the 

Modem cable is firmly connected to the Modem jack. 

            

 

If a connector is disconnected, connect it firmly and repeat Procedure 1. If the 
modem is still not functioning properly, perform Check 2. 

Check 2  The MDC may be defective or damaged. Replace it with a new one following the 

steps in Chapter 4, 

Replacement Procedures

. If the modem is still not functioning 

properly, perform Check 3. 

Check 3  The modem jack or MDC cable may be defective or damaged. Replace it with a 

new one following the steps in Chapter 4, 

Replacement Procedures

. If the modem 

is still not functioning properly, perform Check 4. 

Check 4  The system board may be defective or damaged. Replace it with a new one 

following the steps in Chapter 4, 

Replacement Procedures

. 

 

2-46

 

[CONFIDENTIAL]

 

TECRA M9 Maintenance Manual (960-631) 

Summary of Contents for Tecra M9































































































































































































































































































































































































































Reviews:

No comments