manualshive.com logo in svg

Toshiba Tecra M9, Maintenance Manual

Share
Download
Toshiba Tecra M9 Maintenance Manual Download Page 222

3  Tests and Diagnostics 

3.31 SETUP 

3-96 

[CONFIDENTIAL] 

TECRA M9 Maintenance Manual (960-631) 

NOTE: 

The brightness is when a AC adaptor is connected. When powered by a battery 
it is displayed as follows.  

   

 

 Battery Save Mode = Full power :  LCD Bright ness = Bright. 

   

 

 Battery Save Mode = Low power:  LCD Bright ness = Semi-Bright. 

(a)

 

Battery Save Mode 

When “User Setting” is selected, the sub-window, BATTERY SAVE 
OPTION is displayed. The following set of options can be selected in the 
submenu. 

Processing Speed

This feature changes the CPU processing speed. 

High

   

 

 

CPU operates at high speed. (Default) 

Low

   

 

 

CPU operates at low speed.  

 

CPU Sleep Mode 

Use this option to enable or disable the CPU sleep function.  

Enabled

   

 

Enables sleep mode. (Default) 

Disabled

 

  Disables 

sleep 

mode. 

LCD Brightness

Use this option to set the level of LCD brightness. 

Super-Bright

  

Full brightness for maximum visibility. 

Bright

  

 

 

Full brightness for high visibility. (Default) 

Semi-Bright

   

Less than full brightness for saving power. 

Cooling Method 

If the CPU becomes too hot, the fan turns on or the processing speed is 
lowered automatically. When the CPU temperature falls to a normal range, the 
fan turns off. 

Maximum performance

  

If the CPU becomes too hot, the fan turns on 
automatically at a high speed to cool down the 
CPU.(Default) 

Performance

   

 

 

 

If the CPU becomes too hot, the fan turns on 
automatically. When the CPU temperature falls 
to a normal range, the fan turns off. 

Summary of Contents for Tecra M9































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands