manualshive.com logo in svg

Toshiba Tecra M9, Maintenance Manual

Share
Download
Toshiba Tecra M9 Maintenance Manual Download Page 157

3.14 Real Timer Test 

3  Tests and Diagnostics 

TECRA M9 Maintenance Manual (960-631) 

[CONFIDENTIAL] 

3-31 

Subtest 03 

Real time carry 

CAUTION

:   

When this subtest is executed, the current date and time are erased. 

This subtest checks the real time clock increments, making sure the date and 
time are displayed in the following format: 

Current date  :  12-31-1999 

Current time  :  23:59:58 

The real time increments are automatically executed and the following is 
displayed: 

Current date :  01-01-2000 

Current time :  00:00:00 

PRESS [Enter] KEY TO EXIT TEST  

To exit the test, press 

Enter

.  

Summary of Contents for Tecra M9































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands