manualshive.com logo in svg

Toshiba Tecra M9, Maintenance Manual

Share
Download
Toshiba Tecra M9 Maintenance Manual Download Page 82

2  Troubleshooting Procedures 

2.5 USB FDD Troubleshooting

 

2-32 [CONFIDENTIAL]

 

TECRA M9 Maintenance Manual (960-631) 

Procedure 2 

Diagnostic Test Program Execution Check 

Insert the Diagnostics Disk in the USB FDD, turn on the computer and run the test. Refer to 
Chapter 3, 

Tests and Diagnostics,

 for more information about the diagnostics test procedures. 

Floppy disk drive test error codes and their status names are listed in Table 2-6. Make sure 
the floppy disk is formatted correctly and that the write protect tab is disabled. If any other 
errors occur while executing the FDD diagnostics test, go to Check 1. 

Table 2-6  FDD error code and status 

Code Status 

01h 

Bad command error 

02h 

Address mark not found 

03h Write 

protected 

04h 

Record not found 

06h Media 

removed 

08h 

DMA overrun error 

09h 

DMA boundary error 

10h CRC 

error 

20h FDC 

error 

40h Seek 

error 

60h 

Not drive error 

80h 

Time out error  

EEh 

Write buffer error 

 

Check 1  If the following message appears, disable the write protect tab on the floppy disk. 

If any other message appears, perform Check 2. 

Write protected

 

Check 2  Make sure the floppy disk is formatted correctly. If it is, go to Procedure 3. 

Summary of Contents for Tecra M9































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands