manualshive.com logo in svg

Toshiba Tecra M9, Maintenance Manual

Share
Download
Toshiba Tecra M9 Maintenance Manual Download Page 168

3  Tests and Diagnostics 

3.20 ONLY ONE TEST 

 

3.20.1 Subtest 1 

Pressed key display 

When you execute this subtest, the keyboard layout is drawn on the display as 
shown below. When any key is pressed, the corresponding key on the screen 
changes to the key character that was pressed. Holding a key down enables 
the auto-repeat function that causes the key’s display character to blink. 

Press 

Del

 +

 Enter

 to end the test. 

 

NOTE

:  The actual display may be different from the above image, according to the 

model.  

 

 

 

3-42 

[CONFIDENTIAL] 

TECRA M9 Maintenance Manual (960-631) 

Summary of Contents for Tecra M9































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands