manualshive.com logo in svg

Toshiba Tecra M9, Maintenance Manual, Page: 209 / 414

Share
Download
Toshiba Tecra M9 Maintenance Manual Download Page 209

3.31 SETUP 

3  Tests and Diagnostics 

TECRA M9 Maintenance Manual (960-631) 

[CONFIDENTIAL] 

3-83 

3.31 SETUP 

3.31.1  Function Description 

This program displays the current system setup information as listed below: 

1.

 

Memory 

(a)

 

Total 

2.

 

System Date/Time 

(a)

 

Date (MM-DD-YYYY) 

(b)

 

Time (HH:MM:SS) 

4.

 

Password 

(a)

 

User Password 

(b)

 

Supervisor Password 

5.

 

HDD Password 

(a)

 

HDD 

(b)

 

HDD Password Mode 

(c)

 

User Password 

(d)

 

Master Password 

6.

 

Boot Priority 

(a)

 

Boot Priority 

(b)

 

HDD Priority 

7.

 

Others 

(a)

 

Core Multi-Processing 

(b)

 

Dynamic CPU Frequency Mode 

(c)

 

Execute-Disable Bit Capability 

(d)

 

Virtualization Technology 

(e)

 

Auto Power On 

(f)

 

Beep Volume 

(g)

 

Diagnostic Mode 

Summary of Contents for Tecra M9































































































































































































































































































































































































































Reviews:

No comments