manualshive.com logo in svg

Toshiba Tecra M9, Maintenance Manual

Share
Download
Toshiba Tecra M9 Maintenance Manual Download Page 409

Appendix G  BIOS rewrite procedures 

Appendices

 

G  

Appendix G  BIOS rewrite procedures 

This Appendix explains how to rewrite the system BIOS program when you update the 
system BIOS. 

Tools 

To rewrite the BIOS, you need the following tool: 

‰

 

BIOS/EC/KBC rewriting disk for the computer that has renewed BIOS data. 

Rewriting the BIOS

 

1.

 

Set the system to boot mode. 

2.

 

Turn off the power to the computer. 

3.

 

Remove the external cable and PC card. 

4.

 

Connect an USB FDD and insert the BIOS/EC/KBC rewriting disk into the USB 
FDD. 

5.

 

Turn on the power while holding down the tilde character key until a beep sounds. 

For example 

  

(US Keyboard) 

  (UK Keyboard) 

 

6.

 

The BIOS rewriting starts 

7.

 

When the process is completed, it beeps and the system automatically reboots. 

 

NOTE: 

1.  Connect the AC adapter to the computer when you rewrite the BIOS. 

 

2.  Do not turn off the power while you are rewriting the BIOS. If the rewrite 

fails, it might be impossible to start up the computer. 

 

3  If you fail to rewrite BIOS, then when you next turn on the power, a message 

may be displayed that the contents of the BIOS have been erased.  In this 
case, insert the BIOS rewriting disk and the BIOS will be rewritten. 

 

 

G

 

TECRA M9 Maintenance Manual (960-631) 

[CONFIDENTIAL] 

G-1 

Summary of Contents for Tecra M9































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands