manualshive.com logo in svg

Toshiba Tecra M9, Maintenance Manual

Share
Download
Toshiba Tecra M9 Maintenance Manual Download Page 205

3  Tests and Diagnostics 

5.

 

Select “Diagnostics” tab and click “Run”.

 

 

6.

 

Check the “Log” to confirm the test result. 

 

BT address of test computer 

BT address of responder 
device 

7.

 

When the BT (Bluetooth) address of the responder device appears, the Bluetooth card 
and antenna connection are OK. 
If the BT address of the responder device does not appear, check the Bluetooth card 
condition and antenna cable connection to the Bluetooth card by disassembling the 
computer following the steps described in Chapter 4, 

Replacement Procedures

. 

 

 

TECRA M9 Maintenance Manual (960-631) 

[CONFIDENTIAL] 

3-79 

Summary of Contents for Tecra M9































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands