Toshiba Tecra M9 Maintenance Manual Download Page 26

Page: 26 / 414

1 Hardware Overview

1.2 System Unit Block Diagram

[CONFIDENTIAL]

TECRA M9 Maintenance Manual (960-631)

Cardbus controller (

TI PCI8412ZHK

)

−

PCI Interface(PCI Rev.2.2)

−

SD IO Controller(Ver.1.1)

−

CardBus / Ultra media Controller (Yenta Ver.2.2:1 socket)

−

SD/MMC(SDHC Ver. 1.2 revised edition) , Memory Stick, Memory Stick

pro, XD Card Controller

−

1394 Controller

−

16 x16x1.4mm BGA Package

−

VGA

Graphics interface in North Bridge (Intel Crestline-GM) is used.

Sound Controller

•

Azalia

•

Amplifier: Mathushita made AN12941A

•

Stereo speakers

•

Digital volume control

•

Supports VoIP

•

Stereo headphone jack

•

External microphone jack

•

Built-in microphone

EC/KBC (Embedded Controller/Keyboard Controller)

•

One Mitsubishi M306KAFCLPR micon chip functions as both EC and KBC.

Summary of Contents for Tecra M9































































































































































































































































































































































































































Search results

Summary of Contents for Tecra M9

Reviews:

Brands by name

Popular brands

Toshiba Tecra M9, Maintenance Manual

Search results

Summary of Contents for Tecra M9

Reviews:

Brands by name

Popular brands