Toshiba Tecra M9 Maintenance Manual Download Page 306

Page: 306 / 414

4 Replacement Procedures

4.24 LCD unit/FL inverter

4.24 LCD unit/FL inverter

4.24.1 Removing the LCD unit/FL inverter

The following describes the procedure for removing the LCD unit/FL inverter. (See Figure 4-
40 to 4-44.)

Peel off the

mask seals

(6 points)

and remove the following

screws

securing the LCD

unit.

•

M2.5

FLAT HEAD screw

Remove the keyboard cover while releasing latches. (In the case of removing the
LCD unit before removing the keyboard.)

Release the latches fixing the display rear cover to the LCD mask in the order from
the top to both sides and lay the

display rear cover

down as shown in the figure

below.

Mask seal

M2.5

6B FLAT HEAD

M2.5

6B FLAT HEAD

Display rear cover

LCD mask

Figure 4-41 Raying the display rear cover

4-72

[CONFIDENTIAL]

TECRA M9 Maintenance Manual (960-631)

Summary of Contents for Tecra M9































































































































































































































































































































































































































Search results

Summary of Contents for Tecra M9

Reviews:

Brands by name

Popular brands

Toshiba Tecra M9, Maintenance Manual

Search results

Summary of Contents for Tecra M9

Reviews:

Brands by name

Popular brands