manualshive.com logo in svg

Toshiba Tecra M9, Maintenance Manual

Share
Download
Toshiba Tecra M9 Maintenance Manual Download Page 77

2.4 System Board Troubleshooting 

2  Troubleshooting Procedures

 

TECRA M9 Maintenance Manual (960-631) 

[CONFIDENTIAL]

 

2-27 

Table 2-5  Serial port (Boot mode) error status (7/9) 

D port Status 

Test item 

Contents 

F10Fh 

INIT_SYSTEM  

(Initialization of system) 

 

 

Storing of CMOS error information to 
IRT_ERR_STS_BUF 

 

 

Timer initialization start 

 

 

EC initialization & Reading of battery information 

 

 

Update of system BIOS (Update EDID information for 
LCD) 

F110h 

INIT_DISPLAY 

(Waiting for VGA chip initialization completion, VGA 
BIOS initialization) 

F111h 

VGA POST

 

 

F113h DISP_LOGO 

(Logo 

displaying) 

 

F114h 

SYS_MEM_CHECK 

(Check of conventional memory) (Boot) 

F115h 

EXT_MEM_CHECK 

(Exception check in protected mode) (Boot) 

F116h INIT_SYS_MEM 

 

(Initialization of conventional memory) (Reboot) 
(LED=17h if error occurred during exception check in 
protected mode) 

F118h 

CHK_DMA_PAGE 

(Check of DMA Page Register) (Boot) 

F119h 

CHECK_DMAC 

(Check of DMAC) (Boot) 

F11Ah 

INIT_DMAC 

(Initialization of DMAC) (Boot) 

F11Bh 

CHECK_PRT 

(Check of printer existence) (For models supporting 
Printer port) 

F11Ch 

CHECK_SIO 

(Check of SIO) (model supporting SIO) 

F11Dh BOOT_PASSWORD 

(Check 

of 

password) 

 

 

Waiting for FDD initialization completion  (For models 
supporting built-in FDD) 

 

(In the case of “Reboot”) 

Waiting for HDD initialization completion 

 

 

Check of key input during IRT (waiting for KBC 
initialization completion) 

 

 

Initialization of ATA priority 

 

(In the case of “Boot”) 

Loading processing of BM 

(Only model which is 

supporting the finger point leader) 

 

 

Initialization of BM

(Only model which is supporting the 

finger point leader)

 

 

 

Check of key input during IRT (waiting for KBC 
initialization completion) 

 

 

A password input is performed.

 

 

Summary of Contents for Tecra M9































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands