manualshive.com logo in svg

Toshiba Tecra M9, Maintenance Manual

Share
Download
Toshiba Tecra M9 Maintenance Manual Download Page 315

4.25 LCD cable 

4  Replacement Procedures 

4.25 LCD cable 

Removing the LCD cable 

The following describes the procedure for removing the LCD cable. (See Figure 4-44 and 4-
45.) 

1.

 

Close the hinges and turn over the cover assembly and peel off the 

acetate tape 

fixing the LCD cable. When closing the hinges, be careful not to push the upper 
portion of them. 

2.

 

Turn over the cover assembly and open the display 

3.

 

Pass the 

LCD cable 

and the 

connector

 through the holes of the cover assembly and 

LCD mask from the front to the back and remove the LCD cable on the back of the 
LCD mask.  

 

LCD cable

Acetate tape  
(At the back of the cover 

assembly) 

Hole

Hole 

Connector

Figure 4-46   Removing the LCD cable 

Installing the LCD cable 

The following describes the procedure for installing the LCD cable. (See Figure 4-44 and 4-
45.) 

1.

 

Pass the 

LCD cable

 and the 

connector

 trough the holes of the LCD mask and cover 

assembly

 

from the back to the front. 

2.

 

Close the hinges and turn over the cover assembly and arrange the LCD cable on the 
cover assembly. 

3.

 

Stick the 

acetate tape

 on the LCD cable. 

TECRA M9 Maintenance Manual (960-631) 

[CONFIDENTIAL] 

4-81 

Summary of Contents for Tecra M9































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands