manualshive.com logo in svg

Toshiba Tecra M9, Maintenance Manual

Share
Download
Toshiba Tecra M9 Maintenance Manual Download Page 257

4.8 Switch board 

4  Replacement Procedures 

4.8 Switch 

board 

Removing the Switch board 

The following describes the procedure for removing the switch board. (See Figure 4-12.) 

1.

 

Disconnect the 

switch cable

 from the connector on the switch board. 

2.

 

Push the 

hook 

down and remove the 

switch board 

from the slot

 

while sliding it as 

shown in the figure below. 

 

Switch cable  

Switch board 

Hook 

Figure 4-12  Removing the switch board 

Installing the Switch board 

The following describes the procedure for installing the switch board. (See Figure 4-12.) 

1.

 

Install the 

switch board

 to the slot while sliding it in the opposite direction at 

removing. 

2.

 

Connect the 

switch cable

 to the connector on the switch board. 

TECRA M9 Maintenance Manual (960-631) 

[CONFIDENTIAL] 

4-23

 

Summary of Contents for Tecra M9































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands