Toshiba Tecra M9 Maintenance Manual Download Page 179

Page: 179 / 414

3.23 Running Test

3 Tests and Diagnostics

TECRA M9 Maintenance Manual (960-631)

[CONFIDENTIAL]

3-53

3.23 Running

Test

3.23.1 Function Description

This function automatically executes the following tests in sequence:

System test (subtest 01)

Memory test (subtests 01, 02)

Display test (subtest 01)

Real timer test (subtest 02)

HDD test (subtest 01)

FDD test (subtest 02)

The system automatically detects the number of floppy disk drives connected to the computer
for the FDD test.

3.23.2 Operations

NOTE

: After booting up the Running test, pull out the test program and insert a floppy

disk which has been formatted by FORMAT command of DOS.

Pull out the test program and insert a floppy disk which has been formatted by
FORMAT command of DOS.

Select

from the DIAGNOSTIC MENU and press

Enter

the following messages

for selectable tests will appear in the display in order.

FDD write/read test (Y/N) ?
Printer wrap around test (Y/N) ?
Serial wrap around test (Y/N) ?
CD-ROM/DVD-ROM read test (Y/N) ?

To execute the test, press

and

Enter

. To cancel the test, press

and

Enter

. If you

select the selectable tests, follow the instruction message in the display.

After selecting the selectable tests, the running test starts automatically. To terminate
the program, press

Ctrl

Break

Summary of Contents for Tecra M9































































































































































































































































































































































































































Search results

Summary of Contents for Tecra M9

Reviews:

Brands by name

Popular brands

Toshiba Tecra M9, Maintenance Manual

Search results

Summary of Contents for Tecra M9

Reviews:

Brands by name

Popular brands