manualshive.com logo in svg

Toshiba Tecra M9, Maintenance Manual

Share
Download
Toshiba Tecra M9 Maintenance Manual Download Page 89

2.7 Keyboard and Dual point Troubleshooting 

2  Troubleshooting Procedures

 

TECRA M9 Maintenance Manual (960-631) 

[CONFIDENTIAL]

 

2-39 

2.7 Keyboard 

and 

Dual point Troubleshooting 

To determine if the computer’s keyboard or touch pad is functioning properly, perform the 
following procedures. Start with Procedure 1 and continue with the other procedures as 
instructed. 

Procedure 1:  Diagnostic Test Program Execution Check 
Procedure 2:  Connector Check and Replacement Check 

Procedure 1 

Diagnostic Test Program Execution Check 

Execute the Keyboard Test in the Diagnostic Program. Refer to Chapter 3, 

Tests and 

Diagnostics

, for more information on how to perform the test program. 

If an error occurs, go to Procedure 2. If an error does not occur, the keyboard is functioning 
properly. 

Summary of Contents for Tecra M9































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands