manualshive.com logo in svg

Toshiba Tecra M9, Maintenance Manual

Share
Download
Toshiba Tecra M9 Maintenance Manual Download Page 201

3.28 LAN/Modem/Bluetooth/IEEE1394 Test Program 

3  Tests and Diagnostics  

Subtest01 

( ICHx) 

This subtest checks the operation of mini-PCI I/F by the loopback test in the 
chip.  

The following message will appear: 

[LAN transmit & receive test !] 
       COMPLETED Repeat 

count 

=  00000 

Error count  = 

00000 

LOOPBACK TEST 
100Mbps Auto-negotiation TxRx Test 

 Destination Address    = xxxxxxxxxxxx 

 

Source 

Address    = 

xxxxxxxxxxxx 

  ** 100Base-TX Full-Duplex ** 

  < TRANSMIT > 

  < RECEIVE > 

 

NOTE

:  The menu displayed by your computer may be slightly different from the one 

shown above. 

    If 

a 

defective 

is 

found, 

NG

 message will appear in the display.

 

TECRA M9 Maintenance Manual (960-631) 

[CONFIDENTIAL] 

3-75 

Summary of Contents for Tecra M9































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands