manualshive.com logo in svg

Toshiba Tecra M9, Maintenance Manual

Share
Download
Toshiba Tecra M9 Maintenance Manual Download Page 110

2  Troubleshooting Procedures  

2.17 Fingerprint sensor Troubleshooting

 

2.17  Fingerprint sensor Troubleshooting 

CAUTION

:  To delete the account for confirming the fingerprint operation, it is 

necessary to log on by the account with the management authority. If the 
password has been set to log on, ask the Log-ON password to the user. 

To check if the Fingerprint sensor works correctly or not, follow the troubleshooting 
procedures below as instructed. 

When failed in Procedure 1 to Procedure 3, execute Procedure 4. 

Procedure 1:  Setting Windows Log-ON password 
Procedure 2:  Registration of fingerprint 
Procedure 3:  Authentication of fingerprint 
Procedure 4:  Connector Check and Replacement Check 

CAUTION

:  Scan your finger shown below. 

1. Lay your finger straight to the sensor and put lightly the first joint of your  
    finger at the centerline of the fingerprint sensor. 
2. Slide slowly your finger from the first joint to fingertip at constant speed. 
   When not recognized, adjust the speed. 

 

 

Fingerprint  
  sensor 

Fingerprint  
  sensor 

2-60

 

[CONFIDENTIAL]

 

TECRA M9 Maintenance Manual (960-631) 

Summary of Contents for Tecra M9































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands