manualshive.com logo in svg

Toshiba Tecra M9, Maintenance Manual

Share
Download
Toshiba Tecra M9 Maintenance Manual Download Page 180

3  Tests and Diagnostics 

3.24 Floppy Disk Drive Utilities 

3-54 

[CONFIDENTIAL] 

TECRA M9 Maintenance Manual (960-631) 

3.24  Floppy Disk Drive Utilities 

3.24.1 Function Description 

This function formats the FDD, copies the floppy disk and displays the dump list for both the 
FDD and HDD. 

1.

 

FORMAT 

NOTE

:  This program is only for testing a floppy disk drive. It is different from the 

Toshiba DOS FORMAT command. 

This program can format a floppy disk in the following formats: 

(a)

 

2DD: Double-sided, double-density, double-track, 96/135 TPI, MFM mode, 
512 bytes, 9 sectors/track. 

(b)

 

2HD: Double-sided, high-density, double-track, 96/135 TPI, MFM mode, 512 
bytes, 18 sectors/track. 

2.

 

COPY 

This program copies data from a source floppy disk to a target floppy disk. 

3.

 

DUMP 

This program displays the contents of the floppy disk and the designated sectors of 
the hard disk on the display.  

4.

 

HDD ID READ 

This program reads the hard disk ID and displays hard disk information. 

Summary of Contents for Tecra M9































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands