manualshive.com logo in svg

Toshiba Tecra M9, Maintenance Manual

Share
Download
Toshiba Tecra M9 Maintenance Manual Download Page 139

3.5 Subtest Names

  

3  Tests and Diagnostics 

TECRA M9 Maintenance Manual (960-631) 

[CONFIDENTIAL] 

3-13 

3.5 Subtest 

Names 

Table 3-1 lists the subtest names for each test program in the DIAGNOSTIC TEST MENU. 

Table 3-1 Subtest names (1/2) 

No. 

Test Name 

Subtest No. 

Subtest Name 

1 SYSTEM 

01 
02 
03 
04 
05 

ROM checksum 
Fan ON/OFF 
Geyserville 
Quick charge 
DMI read  

2 MEMORY 

01 
02 
03 
04 
05 

Conventional memory 
Protected Mode 
Protected Mode (cache off) 
Cache memory (on/off) 
Stress 

3 KEYBOARD 

01 

Pressed key code display 

4 DISPLAY 

01 
02 
03 
04 
05 
06 
07 

VRAM read/write for VGA 
Gradation for VGA 
Gradation for LCD 
Gradation & Mode test for VGA 
All dot on/off for LCD 
“H” pattern display 
LCD Brightness 

5 FLOPPY 

DISK 

01 
02 
03 
04 
05 

Sequential read 
Sequential read/write 
Random address/data 
Write specified address 
Read specified address 

Summary of Contents for Tecra M9































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands