manualshive.com logo in svg

Toshiba Tecra M9, Maintenance Manual

Share
Download
Toshiba Tecra M9 Maintenance Manual Download Page 109

2.16 SD Card Slot Troubleshooting 

2  Troubleshooting Procedures

 

2.16  SD Card Slot Troubleshooting 

This section describes how to determine if the computer’s SD card functions are functioning 
properly. Perform the steps below starting with Procedure 1 and continuing with the other 
procedures as required. 

Procedure 1:  Check on Windows  
Procedure 2:  Connector Check and Replacement Check 

Procedure 1 

Check on Windows  

Insert an SD card into the slot. Check if the installed Windows recognizes automatically the 
SD card and the data in the SD card can be read. 

If the card is not recognized or data are not red, go to Procedure 2. 

Procedure 2 

Connector Check and Replacement Check 

The SD card is connected to IS2150 on the System Board. 

 

Check 1  The SD card and the System Board may be disconnected. Make sure the SD card 

is firmly inserted to IS2150 on the System Board. If not, insert it firmly. If the SD 
card is still not functioning properly, perform Check 2. 

Check 2  The SD card may be faulty. Replace it with a new one following the step in 

Chapter 4

 Replacement Procedures

. If the problem continues, perform Check 3. 

Check 3  The System Board may be faulty. Replace it with a new one following the step in 

Chapter 4

 Replacement Procedures

. 

TECRA M9 Maintenance Manual (960-631) 

[CONFIDENTIAL]

 

2-59 

Summary of Contents for Tecra M9































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands