manualshive.com logo in svg

Toshiba Tecra M9, Maintenance Manual

Share
Download
Toshiba Tecra M9 Maintenance Manual Download Page 42

1  Hardware Overview 

1.9 Batteries 

 

28 

[CONFIDENTIAL] 

TECRA M9 Maintenance Manual (960-631)

 

1.9.2 

Battery Charging Control 

Battery charging is controlled by a power supply microprocessor. The microprocessor 
controls whether the charge is on or off and detects a full charge when the AC adaptor and 
battery are attached to the computer.  The system charges the battery. 

Battery Charge 

When the AC adaptor is attached, there are two types of charge: When the system is powered 
off and when the system is powered on. Table 1-8 lists the charging time required for charges. 

Table 1-8   Time required for charges 

Battery type 

Power on 

(hours)

 Power 

off 

(hours)

 

Battery(4,000 mAh) 

About 4.5 to 9.5  

About 2.5  

Battery(5,100 mAh) 

About 5.5 to 12.0  

About 3.0 

Extended capacity  

Battery(7,050 mAh) 

About 8.0 to 19.5  

About 3.5  

High capacity battery(8,800 mAh) 

About 9.0 to 21.0  

About4.0  

NOTE:

  The time required when the system is powered on is affected by the amount of 

power the system is consuming.  Use of the fluorescent lamp and frequent disk 
access diverts power and lengthens the charge time. 

If any of the following occurs, the battery charge process stops.  

1.  The battery becomes fully charged.  

2.  The AC adaptor or battery is removed.  

3.  The battery or output voltage is abnormal.  

‰

 

Detection of full charge 

A full charge is detected only when the battery is charging at charge. A full charge is 
detected under any of the following conditions:  

1.  The current in the battery charging circuit drops under the predetermined limit. 

2.  The charging time exceeds the fixed limit. 

Summary of Contents for Tecra M9































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands