manualshive.com logo in svg

Toshiba Tecra M9, Maintenance Manual

Share
Download
Toshiba Tecra M9 Maintenance Manual Download Page 271

4.12 Wireless LAN card/3G card 

4  Replacement Procedures 

 

(Wireless LAN card (2 antenna cables)/3G card) 

6.

 

Secure the wireless LAN card

 

with the following 

screws

.  

•

 

M2

×

4B     

BIND screw     

×

2 

7.

 

Secure the 3G card

 

with the following 

screws

.  

•

 

M2

×

4B     

BIND screw     

×

2 

8.

 

Stick a new 

insulator

 that prevents a waterdrop from entering the computer. 

NOTE:

  Do not reuse the removed insulator. 

 

TECRA M9 Maintenance Manual (960-631) 

[CONFIDENTIAL] 

4-37

 

Summary of Contents for Tecra M9































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands