manualshive.com logo in svg

Toshiba Tecra M9, Maintenance Manual

Share
Download
Toshiba Tecra M9 Maintenance Manual Download Page 103

2.13 Wireless LAN Troubleshooting 

2  Troubleshooting Procedures

 

TECRA M9 Maintenance Manual (960-631) 

[CONFIDENTIAL]

 

2-53 

Procedure 3 

Replacement Check 

The wireless LAN antenna, wireless LAN board and the system board are connected to the 
circuits. Any of these components may be damaged. Refer to Chapter 4, 

Replacement 

Procedures,

 for instructions on how to disassemble the computer and then perform the 

following checks: 

Check 1  The wireless LAN board may be defective or damaged. Replace the board with a 

new one following the steps in Chapter 4, 

Replacement Procedures

. If the 

problem still exists, perform Check 2. 

Check 2  The wireless LAN antenna may be defective or damaged. Replace the antenna 

with a new one following the steps in Chapter 4, 

Replacement Procedures

. If the 

problem still exists, perform Check 3. 

Check 3  The system board may be defective or damaged. Replace the board with a new 

one following the instructions in Chapter 4, 

Replacement Procedures

 and test the 

display again. 

Summary of Contents for Tecra M9































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands