Toshiba Tecra M9 Maintenance Manual Download Page 333

Page: 333 / 414

4.29 Fluorescent Lamp

4 Replacement Procedures

Assembly of outside Tape and Cover shield

Assembly of Cover shield (S).

CAUTION

: Pressure or stress should not be given on Source PCB.

Usage of gloves with anti-electric discharge coating is recommended.
To eliminate possible damage on circuits occurred by ESC.

Assembly of Cover shield (G).

CAUTION

: Pressure or stress should not be given on Gate COF.

Assembly of Tape Adhesive used for Top case fixing.

CAUTION

: Pressure or stress should not be given on Top case during this process.

Figure 4-59 Replacing LG.Philips fluorescent lamp (WXGA) (8)

TECRA M9 Maintenance Manual (960-631)

[CONFIDENTIAL]

4-99

Summary of Contents for Tecra M9































































































































































































































































































































































































































Search results

Summary of Contents for Tecra M9

Reviews:

Brands by name

Popular brands

Toshiba Tecra M9, Maintenance Manual

Search results

Summary of Contents for Tecra M9

Reviews:

Brands by name

Popular brands