manualshive.com logo in svg

Toshiba Tecra M9, Maintenance Manual

Share
Download
Toshiba Tecra M9 Maintenance Manual Download Page 92

2  Troubleshooting Procedures  

2.8 Display Troubleshooting

 

2-42

 

[CONFIDENTIAL]

 

TECRA M9 Maintenance Manual (960-631) 

If the connection is loose, reconnect firmly and restart the computer. If there is still an error, 
go to Procedure 4. 

Procedure 4 

Replacement Check 

The FL, FL inverter board, LCD module, and system board are connected to display circuits. 
Any of these components may be damaged. Refer to Chapter 4, 

Replacement Procedures,

 for 

instructions on how to disassemble the computer and then perform the following checks: 

1.

 

If the FL does not light, perform Check 1. 

2.

 

If characters or graphics are not displayed clearly, perform Check 1. 

3.

 

If some screen functions do not operate properly, perform Check 2. 

4.

 

If the FL remains lit when the display is closed, perform Check 4. 

Check 1  Replace the FL with a new one following the instructions in Chapter 4, 

Replacement Procedures

 and test the display again. If the problem still exists, 

perform Check2. 

Check 2  Replace the LCD module with a new one following the instructions in Chapter 4, 

Replacement Procedures

 and test the display again. If the problem still exists, 

perform Check 3. 

Check 3  Replace the display cable (FL cable and LCD cable) with a new one following the 

instructions in Chapter 4, 

Replacement Procedures

 and test the display again. If 

the problem still exists, perform Check 4. 

Check 4  The display controller on the system board may be damaged. Replace the system 

board with a new one following the instructions in Chapter 4, 

Replacement 

Procedures

.  

 

Summary of Contents for Tecra M9































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands