Toshiba Tecra M9 Maintenance Manual Download Page 86 | Manualshive

Page: 86 / 414

Toshiba Tecra M9 Maintenance Manual Download Page 86

2 Troubleshooting Procedures

2.6 HDD Troubleshooting

2-36

[CONFIDENTIAL]

TECRA M9 Maintenance Manual (960-631)

Procedure 3

Format Check

The computer’s HDD is formatted using the low level format program and the MS-DOS
FORMAT program. To format the HDD, start with Check 1 below and perform the other
steps as required.

Check 1 Format the HDD and transfer system files using

FORMAT C:/S/U

. If the

following message appears on the display, the HDD is formatted.

Format complete

If an error message appears on the display, refer to the Toshiba MS-DOS Manual
for more information and perform Check 2.

Check 2 Using the Diagnostics Disk, format the HDD with a low level format option.

Refer to Chapter 3,

Tests and Diagnostics

for more information about the

diagnostic program.

If the following message appears on the display, the HDD low level format is
complete. Partition and format the HDD using the MS-DOS FORMAT command.

Format complete

If you cannot format the HDD using the Tests and Diagnostic program, go to
Procedure 4.

«
...
84
85
86
87
88
...
»

Summary of Contents for Tecra M9































































































































































































































































































































































































































Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands