manualshive.com logo in svg

Toshiba Tecra M9, Maintenance Manual

Share
Download
Toshiba Tecra M9 Maintenance Manual Download Page 317

4.26 Wireless LAN antenna/Bluetooth antenna/3G antenna 

4  Replacement Procedures 

NOTE:

  When replacing the LCD cover 10C WXGA model with a new one, stick a new 

cushion in place. 

 

Cushion 

 

 

Installing the Wireless LAN antenna/Bluetooth antenna 

The following describes the procedure for installing the wireless LAN antenna/Bluetooth 
antenna. (See Figure 4-46.) 

1.

 

Install the 

wireless

 

LAN antennas

 and 

Bluetooth antenna

 to the display cover. 

2.

 

Arrange the 

wireless LAN antenna cables

 and 

Bluetooth antenna cable

 on the 

display rear cover and secure it with the 

acetate tapes

. 

TECRA M9 Maintenance Manual (960-631) 

[CONFIDENTIAL] 

4-83 

Summary of Contents for Tecra M9































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands