Toshiba MAGNIA 510D User Manual Download

Page: 59 / 185

Connecting Components

Hot-Swap Drive Carrier

Installing a hard disk drive in a drive tray

Place the hard disk drive in the drive tray making sure the I/O connector is flush with
the rear of the tray.

Positioning the hard disk drive in the drive tray

Position the drive tray cover on the drive tray, then secure the hard disk drive and the
cover with four screws.

Securing the drive tray assembly

Removing a hard disk drive from a drive tray

Remove the four screws securing the hard disk drive and disk tray cover to the drive
tray.

CAUTION: To avoid excessive shock to the hard disk drive, work on a soft surface.

For more information on handling your hard disk drive, refer to the manufacturer’s
documentation that came with the drive.

NOTE: If a shield cover is attached to your hard disk drive, you must remove it
before you can install the drive in the drive tray.

NOTE: To position the drive tray cover, insert the front lip of the cover under the front
inside face of the drive tray. Carefully press the rear of the cover into place so that
the side flanges align with the outside of the tray.

Hard disk drive

Drive tray

Hard disk drive

Drive tray

Screw

Drive tray cover

Summary of Contents for MAGNIA 510D


























































































































































































Search results

Summary of Contents for MAGNIA 510D

Reviews:

Related manuals for MAGNIA 510D

Brands by name

Popular brands

Toshiba MAGNIA 510D, User Manual

Search results

Summary of Contents for MAGNIA 510D

Reviews:

Related manuals for MAGNIA 510D

Brands by name

Popular brands