Toshiba MAGNIA 510D User Manual Download

Page: 102 / 185

Software Installation

Installing NetWare

102

Selecting a Network Adapter driver

If the installer detects the network adapter, the following screen appears:

Select "_Continue" and complete the installation by following the on-screen instructions.

Post installation procedures

Setup the RAID Controller Utility

If a RAID controller is connected to the server, be sure to set up the “MegaRAID
Manager” after installing NetWare. If the MegaRAID Manager is not set up, the system
cannot be recovered from disk trouble during operation.

For details, refer to the “MegaRAID Software Guide”.

The following drivers were detected for this server. Add, change,

or delete device drivers as needed.

Device types

Driver names

Storage Devices:

IDECD, SCSIHD

Network boards:

DLH5X

NetWare loadable modules

(optional)

options

_Continue

_Modify

Summary of Contents for MAGNIA 510D


























































































































































































Search results

Summary of Contents for MAGNIA 510D

Reviews:

Related manuals for MAGNIA 510D

Brands by name

Popular brands

Toshiba MAGNIA 510D, User Manual

Search results

Summary of Contents for MAGNIA 510D

Reviews:

Related manuals for MAGNIA 510D

Brands by name

Popular brands