manualshive.com logo in svg

Toshiba MAGNIA 510D, User Manual

Share
Download
Toshiba MAGNIA 510D User Manual Download Page 56

Connecting Components

Hot-Swap Drive Carrier

  56

Hot-Swap Drive Carrier

This section reviews the hot-swap drive carrier.

Drive carrier - Supports SCSI Ultra 160 interfaces with device bays for up to three 
removable drive trays.

Drive tray - Allows you to mount 3.5-inch, low profile, SCA2 SCSI hard disk drives in the 
drive carrier.

Key lock - The key lock:

❖

Ensures the drive tray is properly seated in the drive carrier.

❖

Prevents unauthorized removal of the drive tray from the drive carrier.

❖

Turns power on and off to the drive tray.

NOTE: The hot-swap driver carrier is found on certain models only.

NOTE: The key lock must be engaged (turned counterclockwise) for the drive 
carrier to supply DC power to the drive tray and the installed hard disk drive.

Drive tray

Drive carrier

Key lock (3)

Display panel (3)

Timing switch

Summary of Contents for MAGNIA 510D


























































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands