manualshive.com logo in svg

Toshiba MAGNIA 510D, User Manual

Share
Download
Toshiba MAGNIA 510D User Manual Download Page 21

Getting Started

System overview 

21

❖

Communication and speed lights - The Communication (ACT) and Link lights indicate 
the communication status.

❖

The Link Speed light (100M) indicates the communication speed.

Inside the server

❖

Motherboard - The motherboard can accomodate up to two CPU modules and five 
PCI expansion cards.

❖

5.25-inch device bays - This device has four bays which are accessible from the front 
of the server (one has a CD-ROM drive installed). The server supports built-in SCSI 
devices.

❖

Memory slots - The server has four memory slots that support 64 MB, 128 MB, 256 
MB, and 512 MB modules. See “Adding memory” on page 40 for more information.

On:

Connected normally and waiting

Flashing:

Communicating

Off:

Network cable unconnected or 
connected incorrectly

On:

Communication at 100 Mbps

Off:

Communication at 10 Mbps

Internal battery

Expansion 

Motherboard

CPU sockets

slots

5.25-inch 
device bays

3.5-inch 
device bays

Cooling fan

Cooling fan 

Memory slots

Power supply 

Video card

LAN card

Summary of Contents for MAGNIA 510D


























































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands