background image

  177

orphaned partitions:

 These occur in disk mirroring when the drive containing the master 

partition fails. If a drive containing a duplicate partition fails, the system marks 

the master partition as unmirrored.

operating system:

 A set of programs that controls how the computer works. Operating 

system functions include creating programs and data files, and controlling the 

flow of information between the processor, memory, and devices. Examples of 

operating systems used by computers are MS-DOS, Windows 95/98, and 

Novell NetWare.

operating system disks:

 The disks containing the operating system. Also known as 

system disks.

output:

 The results of a computer operation. Familiar forms of output are information (1) 

printed on paper, (2) displayed on a screen, (3) sent through the serial port or 

internal modem, or (4) stored on disk. See also 

input/output (I/O)

.

P

palette:

 In some programs, a palette is a collection of drawing tools, brush widths, line 

widths, and colors. In other programs, the palette determines the number of 

colors that can be displayed on the screen.

parallel:

 Two or more processes or events that can happen at the same time without 

interfering with each other.

parallel interface:

 A type of information exchange that simultaneously transmits all the 

bits representing a character. It uses a separate line for each data bit in a byte. 

In contrast, a serial interface transmits characters along a single data line one 

bit at a time, making it much slower than a parallel interface.

parity:

 A method in serial communications of making sure that the information received is 

the same as the information that was sent. It consists of adding an error 

detection bit to a group of data bits, making the sum of the bits either odd or 

even. When you’re using a modem to connect to another computer, you can 

set parity to none, odd, or even. In general, you should set parity to none, 

unless you’re requested to do otherwise.

Summary of Contents for MAGNIA 510D


























































































































































































Reviews: