Toshiba MAGNIA 510D User Manual Download

Page: 113 / 185

Hardware Diagnostics

Hardware Diagnostics Program

113

FLOPPY DISK TEST (FDD) Error Log

❖

05. PRINTER TEST checks the operation of the printer port.

- 01. Print Ripple Pattern subtest prints characters for codes 20h through 7Eh line-by-

line while shifting one character to the left at the beginning of each new line. See
below for screen example.

- PRINTER TEST (PRT) Error Log 01.

Status

Error name

Meaning

BAD COMMAND ERROR

Bad command error

ADDRESS MARK NOT FOUND

The address mark has not been
found

WRITE PROTECTED

Floppy disk is write-protected

RECORD NOT FOUND

The record has not been found

MEDIA CHANGE LINE ERROR

The media change line is bad

DMA OVERRUN ERROR

DMA OVERRUN occurred

DMA BOUNDARY ERROR

DMA BOUDARY occurred

CRC ERROR

CRC check error

FDC ERROR

FDC error

DATA COMPARE ERROR

Data comparing error

Status

Error name

Meaning

TIME OUT

Time out of printer control

Summary of Contents for MAGNIA 510D


























































































































































































Search results

Summary of Contents for MAGNIA 510D

Reviews:

Related manuals for MAGNIA 510D

Brands by name

Popular brands

Toshiba MAGNIA 510D, User Manual

Search results

Summary of Contents for MAGNIA 510D

Reviews:

Related manuals for MAGNIA 510D

Brands by name

Popular brands