Toshiba MAGNIA 510D Page 80 User Manual Download

Page: 80 / 185

System Configuration Setup

Setup

❖

Suspend Mode - Determines whether the server enters a low power state when it has
been inactive for a specified length of time.

❖

Display Activity - Sets a power saving mode when the monitor is turned back on.

❖

IRQ3 ~ IRQ15 - Specifies interruptions to be monitored by the Power Saving function.

Set IRQ3 ~ IRQ15 as follows:

IRQ3 - Monitor
IRQ4 - Monitor
IRQ5 - Ignore
IRQ7 - Monitor
IRQ9 - Ignore
IRQ10 - Ignore
IRQ11 - Ignore
IRQ13 - Ignore
IRQ14 - Monitor
IRQ15 - Ignore

❖

Soft-off by PWR-BTTN - Determines whether the Power button switches the server
off immediately or after a 4 second delay.

Disable
(default)

Disables Suspend Mode

1 min to 1 hour

Sets the period of inactivity which causes the
server to enter Suspend Mode

Ignore (default)

Switches to a power saving mode when the
monitor is turned on.

Monitor

Does not switch to a power saving mode
when the monitor is turned on.

Monitor Monitors

interruptions.

Ignore

Ignores interruptions.

Instant-off
(default)

Power Off takes effect immediately

Delay 4 sec.

Soft switch introduces a 4 second delay

Summary of Contents for MAGNIA 510D


























































































































































































Search results

Summary of Contents for MAGNIA 510D

Reviews:

Related manuals for MAGNIA 510D

Brands by name

Popular brands

Toshiba MAGNIA 510D, User Manual

Search results

Summary of Contents for MAGNIA 510D

Reviews:

Related manuals for MAGNIA 510D

Brands by name

Popular brands