Toshiba MAGNIA 510D User Manual Download

Page: 54 / 185

Connecting Components

Adding SCSI I/O devices

Set the SCSI-ID of the SCSI device.

Position the rails on the SCSI device and secure them with four screws. Use “Screw
B” designated in the table

Toshiba supplied hardware items

on page 29.

Installing the rails for a SCSI device

Remove the screws securing the 5.25-inch shield cover and store the cover for
possible reuse.

Removing the shield

Insert the SCSI device into the slot and secure it with two screws.

Inserting the SCSI device

Connect the power cable and the signal cable to the SCSI device.

Reinstall the bezel and side panel. For instructions, see

Removing and installing the

bezel and side panel

on page 31.

Removing SCSI devices

Review the precautions described in

Before you start

on page 27 in this chapter before

removing any SCSI device.

Remove the bezel and side panel. For instructions, see

Removing and installing the

bezel and side panel

on page 31.

Summary of Contents for MAGNIA 510D


























































































































































































Search results

Summary of Contents for MAGNIA 510D

Reviews:

Related manuals for MAGNIA 510D

Brands by name

Popular brands

Toshiba MAGNIA 510D, User Manual

Search results

Summary of Contents for MAGNIA 510D

Reviews:

Related manuals for MAGNIA 510D

Brands by name

Popular brands