Toshiba MAGNIA 510D User Manual Download

Page: 31 / 185

Connecting Components

Removing and installing the bezel and side panel

Removing and installing the bezel and side panel

To access the CPU slots, memory module slots, expansion slots, and device bays, you
need to remove both the bezel and the side panel.

Removing the bezel

Grasp the latch at the bottom edge of the bezel.

Squeeze the latch, then pull it toward the front of the server to release the lower
edge of the bezel from the server chassis.

Removing the bezel

Rotate and lift the bezel away from the server.

CAUTION: Never use force to remove the bezel. Using force may break the bezel’s
hooks.

Bezel

Side panel

Summary of Contents for MAGNIA 510D


























































































































































































Search results

Summary of Contents for MAGNIA 510D

Reviews:

Related manuals for MAGNIA 510D

Brands by name

Popular brands

Toshiba MAGNIA 510D, User Manual

Search results

Summary of Contents for MAGNIA 510D

Reviews:

Related manuals for MAGNIA 510D

Brands by name

Popular brands