THK TJU Instruction Manual Download

Page: 23 / 134

2. Installation

Check products

2-8

TNU

⿟

Prepare a cable to connect TJU and TJU by yourself.

(-> P.3-9)

⿟

When using TNU, 1 TJU unit is required. Up to 3 TJU units can be used.

⿟

A cable to connect to TJU and driver controller is available as an option.

(-> P.2-4)

⿟

A unit is used when connecting multiple driver controllers to the TNU, including the following
functions:

･

7 ports: Input port x 1, Output port x 6

･

LED to check a connection on the output ports (not lighting up in case of the destination is

TJU)

･

Termination resistance change switch

1-4-2

Branch unit TJU

LINE IN

Input port (upper-level connection)

Connect to the TNU or other TJU output port.

TERM.ON/OFF

Termination resistance change switch

Sets the termination resistance to ON or OFF.

* The last TJU only is set to TERM.ON.

PORT

Output port

Connect the driver controller or other TJU.

(FG)

Ground wire is connected.

Connection status display LED

This light is on when the unit is connected to the driver

controller.

• When configuring a system, only for the TJU that is in the farthest location from the TNU, set its termination

resistance change switch to "TERM.ON".

If the termination resistance change switch is not set to "TERM.ON", an error may occur in the TACnet communication.

Important

www.thk.ru

тел. +7(499) 703-39-86

[email protected]

Summary of Contents for TJU







































































































































Search results

Summary of Contents for TJU

Reviews:

Related manuals for TJU

Brands by name

Popular brands

THK TJU, Instruction Manual

Search results

Summary of Contents for TJU

Reviews:

Related manuals for TJU

Brands by name

Popular brands