THK TJU Instruction Manual Download Page 31

Page: 31 / 134

3. Wiring

How to wire

3-3

TNU

1-1

Entire wiring

See the wiring example below.

⿟

The cables to be connected to the CN1 to 4 connectors with

★

mark or between TJUs are not

provided, so please separately prepare them by yourself.

(-> P.3-4) (-> P.3-9)

⿟

A cable to connect to TJU and driver controller is available as an option.

(-> P.2-4)

CN1 upper-level network

communication connector

is provided with TNU.

(TNU-CC, TNU-DV)

TDO(-> P.7-1)

Higher device

The power supply should be
prepared by yourself.
The power connector for CN4 is
provided with TNU. (-> P.3-4)

PC communication cables
are provided as an option.
(-> P.2-4)

★

CN3

Emergency stop switch
This should be prepared
by yourself.

24 V DC power

★

Branch unit TJU
(-> P.3-9)

CN1

CN2

CN4

LINE IN

Termination
resistance OFF
[TERM.OFF]

(-> P.2-8)

Termination
resistance OFF
[TERM.OFF]

(-> P.2-8)

Termination
resistance ON
[TERM.ON]

(-> P.2-8)

Max. 16 axes

Driver controller

Actuator

Network unit

TNU

★

PC (D-STEP) (-> P.6-1)

www.thk.ru

тел. +7(499) 703-39-86

[email protected]

Summary of Contents for TJU







































































































































Search results

Summary of Contents for TJU

Reviews:

Brands by name

Popular brands

THK TJU, Instruction Manual

Search results

Summary of Contents for TJU

Reviews:

Brands by name

Popular brands